2017 Masterwork MK1060ERsl Smartcutter Die Cutter with Blanker

2017 Masterwork MK1060ERsl Smartcutter Die Cutter with Blanker

Max Sheet Size: 1060mm X 760mm

Min Sheet Size: 400mm X 350mm

Max Die Cutting Size: 1045mm X 745mm

Max Foil Stamping Size: 1060mm X 740mm

Gripper Margin: 9~17mm (Standard: 13mm)

Convertible Stock: cardboard: 0.1-2.0mm (90-2000 gsm) Corrugated: ≦4.0mm

Max Feeding Pile Height: 1350 mm

Max Delivery Pile Height: 1150 mm

Max Working Speed: 7500 sheets per hour

Die Cutting Accuracy: ≦±0.075mm

Preset Max Die Cutting Pressure: 260 metric tons

Wattage of Main Drive Motor: 11.0 KW

Power Supply: 380/50Hz/3-phase with grounding 7050mm

Non-stop Feeder

• Stream-wise feeding system with a highest speed of 125 sheets per minute
• Paper speed slow-down at its arrival at front guides
• Height and angle of suction cups are easily adjustable to accommodate paper condition
• 3 anti-crash devices for the protection of suction head due to over-ascending of feeder pile
• Manual adjustment of the transversal position of feeder pile table
• 4 lifting and 5 forwarding suction cups
• Lateral blowing system enhancing paper separation
• Precision electronic-mechanical double sheet detector
• Easy changeover of pull and push side guides simply by turning a bolt without the need of removing and replacing complete side guide
• Side and front guides with photocells
• Single position engagement electromagnetic clutch insures the first sheet after every re-start of machine is always fed to front lays for easy, time-saving and material-saving makeready
• Photo-electric detector with automatic stop system on feeding table in case of paper jam
• Separate drive controls of feeding unit and the main machine for easy makeready
• PLC and electronic cam for timing control
• I set of steel paper support rods for non-stop feeding
• 4 sets each of brush roller assemble for cardboard and paper on feed table
• 10 sets of Nylon roller assembly for paper hold-down on feed table
• 2 sets of press-down steel ball assembly on feed table
• 2 paper pile skids for non-stop feeding
• Steel rack for pre-piling of paper stock
• Becker vacuum pump

Platen Press

• Micro adjustment of cutting force by worm gear driven by servo motor
• Crank shaft made of 40Cr steel
• Machine frames, upper and lower platens made of QT60 ductile iron with resin coated sand with
• Mechanize Die Cast Iron Technology, with weathering and twice heat treatments
• Accurate positioning of Cutting chase controlled by precision photocell sensors
• Cutting chase turn-over device
• Air cooling system for gear box lubrication oil
• Overload protection device with torque limiter for the highest safety of operator and equipment
• 9 Gripper bars made of lightweight and durable aluminum alloy with ultra hard coat and anodized finish
• Ultra low stretch and friction gripper chain made in England
• Patented device for quick compensation of gripper chain elongation
• Brake system of main drive motor with pneumatic clutch for
• 23.5mm support plate for cutting plates made of ultra durable engineering plastic Position of support plate in machine and transversal directions is micro adjustable.
• Pneumatic lock-up and release of cutting chase
• Electronic detector detecting sheet breakage of all sheet size convertible by the machine
• Two universal cutting chase with quick-lock device

Triple Action Stripping Device

• Driving system for upper stripping frame, stripping board and lower stripping frame
• Upper stripping frame with pneumatic lifting device
• Upper stripping frame with pneumatic quick-lock device
• Stripping board with quick-lock device
• Position of stripping frames and stripping board is micro adjustable with digital display
• Aluminum alloy upper stripping frame
• Aluminum alloy lower stripping frame
• Telescopic stripping bar
• Clamp for holder of upper stripping pin
• Clamp for stripping bar
• Lower stripping pin
• Upper stripping pin
• Pin holder

Blanking Device

• Driving system for upper blanking tool
• Pneumatic lifting device for upper blanking tool
• Upper blanking tool with quick-lock device
• Blanking tools with micro adjustment and digital display
• Delivery system for die cut sheets without blanking
• Non-stop stacker for die cut blank
• Delivery of removed edges of sheet

Delivery Unit

• Photo-electric devices control delivery pile height
• Brake brush for sheets discharge from gripper bar
• Steel rack for non-stop delivery

Mechanical, Electric and Safety Devices

• Mitsubishi PLC monitoring and self-diagnostic system with 10.4” and 5.7” touch screen
• Omron Electronic cam and index device
• Becker (Germany) pneumatic pump
• Easily accessible emergency stop switches on entire machine
• Overload protector for the safety of operator and equipment
• All electrical design, wiring and controls meet CE safety standards.

Automatic Lubrication and Cooling System

• Centralized automatic lubrication for the entire machine with automatic oil pump and distribution system
• Air cooling system for lubrication oil of crank shaft
• Automatic lubrication system with preset timer for gripper chains